Cert. No. LRQ 0963008

ISO 9001

Description

The TD62LM and TD62M are maintainable high pressure

thermodynamic steam traps with integral strainer and a replaceable

seat to ease maintenance. They have been specifically designed for

mains drainage applications up to 62 bar g.

The TD62LM is specifically designed for relatively small condensate

loads on superheat and mains drainage applications. An insulating

cover is fitted as standard to prevent the trap being unduly influenced

by excessive heat loss when subjected to low ambient temperatures,

wind or rain.

Standards

This product fully complies with the requirements of the European

Pressure Equipment Directive 97/23/EC.

Certification

This product is available with certification to EN 10204 3.1.

Note: All certification/inspection requirements must be stated at

the time of order placement.

5.7.45

Sizes and pipe connections

DN15, DN20 and DN25

Standard flange to ANSI B 16.5 Class 300 and 600, and JIS / KS 40K.

ANSI Class 150 RF connections are available to special order.

Pressure / temperature limits

���

���

���

���

���

�

9

5

11

A

Steam saturation

curve

D

C

B

�

��

��

��

��

���

Pressure bar g

The product must not be used in this region.

The product should not be used in this region or beyond

Material

its operating range as damage to the internals may occur.

A - B Flanged to ANSI B 16.5 Class 600.

Steel

Steel

Steel

Stainless steel 100 mesh

316L

Aluminium

A - C Flanged to JIS/KS 40K.

A - D Flanged to ANSI B 16.5 Class 300.

Body design conditions

PMA Maximum allowable pressure

TMA Maximum allowable temperature

Minimum allowable temperature

PMO

Maximum operating pressure

for steam service

TMO Maximum operating temperature

Minimum operating temperature

ANSI 600

103 bar g @ 93°C

525°C @ 42.7 bar g

0°C

62 bar g @ 482°C

525°C @ 42.7 bar g

Chromium steel

Chromium steel

Steel

Steel

Steel

ASTM A193 B16

ASTM A193 B16

ASTM A194 8M

PMOB

Maximum operating

backpressure

0°C

TD62LM 50% of upstream pressure

Spirally wound stainless steel

with exfoliated graphite filler

Stainless steel

Spirally wound stainless steel

with exfoliated graphite filler

TD62M

TD62LM

TD62M

Spirally wound stainless steel

with exfoliated graphite filler

80% of upstream pressure

8 bar g

1.4 bar g

Designed for a maximum cold hydraulic test pressure of 155 bar g

Minimum operating pressure

Stainless steel

Steam traps

Thermodynamic

TD62LM and TD62M

Thermodynamic Steam Traps

with replaceable seats ASTM Body (Flanged connections)

Local regulations may restrict the use of this product to below the conditions quoted.

In the interests of development and improvement of the product, we reserve the right to change the specification without notice.

© Copyright 2006

2

6

8

10

14

13

8A

9

Materials

No. Part

1

Body

2

Top cover

3

Bottom cover

4

Strainer screen

5

Insulating cover

6

Disc

* 7

Seat

8

Cover studs (top)

8A Cover studs (bottom)

9

Cover nuts

10 Cover gaskets

11 Name-plate

13 Inner seat gasket

14 Outer seat gasket

* 15 Ferrule

* Note: Item 15 (ferrule) is pressed into item 7 (seat).

7

15

4

1

10

3

TI-P068-20

ST Issue 7

T

e

m

p

e

r

a

t

u

r

e

°

C

ASTM A217 WC6

ASTM A217 WC6

ASTM A217 WC6