Start from the left corner of the

room, having the tongue clinging

to the wall, foreseeing to leave a

perimetral space at least 8 mm,

using spacers (do not fill with

silicone, wires, etc.).

Fix using the tongue-and-groove

method.

Raise along the side of the plank

and cling to it.

For a better visual result, stagger

the planks by 1/3 of their length.

On the perimeter, avoid cuts that

are less than 25 cm long and 10 cm

wide.

SOME RECOMMENDATIONS

Planks must be preferably oriented in the direction of the light that

gets into the room.

• How to make cuts along edges. Make the cut taking 2 planks.

Place the first plank A over the last entire plank that has been

laid. Rest the second plank B in such a way that it touches the

wall. Use plank B as if it was a ruler to cut plank A. Lay the blade.

This procedure must always be applied for cuts along edges.

• Finishesinbathroomsandsanitaryappliances.Sealtheperimeter

edges near the sanitary appliances with suitable anti-mould

silicone or rubber cement that guarantees perfect sealing.

MAINTENANCE

• Precautions for use. Apply felt pads below the legs of furniture

or below heavy objects. Protect the planks from direct heat

sources such as stoves and chimneys. Dyed rubber-based

and castors (castor chairs, tables etc.) may indelible stain the

flooring.

• Floor cleaning. Vacuum cleaner or wet cloth. Use only Detergent

Evo of Virag. Difficult stains: dilute bleach, alcohol or lemon juice.

Ink, tomato, mustard, blood, beet, mercurochrome stains: leave

diluted bleach on for some minutes without scrubbing. Rinse

abundantly. Rust: clean with a rust preserver for fabrics and

rinse abundantly. Grease, ink and felt-tip pen: scrub slightly with

a piece of cloth soaked in alcohol. Rinse abundantly.

• Precautions for maintenance. Absolutely avoid using

acetone and chlorinated solvents (e.g. trichloroethylene).

• Replacement of planks. Cut a corner of the plank to be replaced,

pagina libera

Leave a distance of 8 mm on

remove the plank by pulling from such corner, lay a new plank

the entire room perimeter and

inserting first of all the tongues under the other planks, and

from every obstacle that could

compromise the laying movement.

Once the laying is completed,

remove all spacers and place

proper skirting board. Do not fix the

skirting board on the floor.

then fit it into place.

• Please note. The possible spacing of the joints between the

planks is a natural phenomenon caused by the product ageing

and does not require any intervention.

WARRANTY

Evolution Fast planks are guaranteed from manufacturing defects

from the purchase date. If you have any complaint, go to the store

where the material has been purchased, taking the relative ticket

with you. Laying without Rollsoft underlay is not covered by the

guarantee. The guarantee is limited in time and is applied when the

product has been laid correctly and the maintenance operations

have been carried out in compliance with the instructions for

use. The guarantee covers the replacement, without including

the expenses related to laying and removal, with material of the

same range available at the time of the complaint, of equivalent or

similar quality. It does not cover the natural wear of planks, laying

or maintenance defects, deviant use, scratches, errors by the

user or negligence such as impacts, objects falling down, stains,

cigarette or other burns, damage caused by bad weather or

fires. This guarantee is applied with reservation according to the

national regulations regarding the guarantees that manufacturers

must observe. The company reserves the right to modify the

product characteristics and the relative laying instructions at any

time and without prior notice. Valid only if using Virag’s cleaning

and maintenance product.

IMPORTANT

• Evolution Fast must be laid at an ambient temperature around

20°C.

• Evolution Fast cannot be used in the following cases: verandas,

rooms where temperature can go down below 15°C.

• Evolution Fast is compatible with underfloor heating if the base

temperature is not higher than 27°C at any point, as well as

with cooled/heated floors.

• Keep in storage some planks having the same batch number as

the ones that have been laid for any future repairs.

• Install the expansion joints every mtl.

• The subfloor temperature must be > 15°C.

• In damp rooms and bathroom fill the edge joints with silicone.

• Glue down the flooring when (before removing the underfloor):

- the room temperature changes suddenly and is not constant

between 10°C and 28°C.

- in the presence of heat sources with stoves and fireplaces.

- near door windows, windows and skylights that have no

thermal break or protective film.

50 | EVOLUTION FAST | SPC