EXTENSION OF DECENTAL CONVENTIONAL

WARRANTY

11.1. Subject

All products of the Seller are guaranteed for 10 (ten)

years from the date of issue of the invoice with which

the same products are supplied.

The guarantee provided only concerns the pure and

simple replacement of products or of particular

components of the same which are defective due to a

manufacturing defect such that the products cannot be

used for ordinary use to which they may be destined.

Any guarantee for expenses and / or damages caused

by the defective product to things and / or people is

excluded from the guarantee given here.

The normal obsolescence of the products or of

particular elements of the same is excluded from the

guarantee given here.

The following products are excluded from the

guarantee given here: engines, pipes, gaskets, ...

Products and particular components of the same ones

sold by the Seller but not produced by the same are

excluded from the warranty provided here.

The guarantee provided here is operative throughout

the Italian and European national territory.

The guarantee given here is valid only if the Purchaser

has sent the Seller express acceptance of these

general conditions by signing them at the bottom.

Failing this, the Seller will be required to provide

exclusively the guarantee according to the current

laws.

It is the responsibility of those who intend to activate

the warranty to prove the defect of the manufacture of

the product, the fact that it was not recognizable upon

receipt of the product (see article 10 of these general

conditions), the invoice of the Seller with which the

product was supplied and the signing of the present

general conditions by the Purchaser.

In the absence of even one of these elements, the

Seller will not be required to provide the conventional

guarantee.

In order to be replaced, defective products must be

returned to the Seller in advance.

The return of defective products, in any case, must

always be agreed in advance with the Seller.

The warranty is to be considered valid only in

compliance with the conditions indicated in the

following point 11.2.

The guarantee lapses in the cases indicated in the

following point 11.3.

The external Laying and Protection Indications

indicated in the following point 11.4 must always be

observed.

11.2. Conditions

•

Pipes and fittings must be installed according

to the instructions contained in the installation manual,

defined in the general catalog of the Seller.

•

No tampering or alteration of the products

must have occurred after the production period, even

only due to accidental causes.

•

The operating conditions (temperatures,

pressures, nature of liquids, tensioning) must fall within

the parameters indicated in the installation manual,

defined in the general catalog of the Seller.

•

The items object of request must expressly

bring the trademarks.

11.3. Decadency

•

Failure or incorrect observance, even partial, of

the installation instructions provided by the

manufacturer.

•

Missed or incorrect observance of the rules of

art or of the specific rules of good technique.

•

Use of deteriorated and therefore unsuitable

materials: pipes and fittings that have been aged or

scratched, crushed, etc..

•

Use of materials not supplied by the Seller

(pipes and

fittings).

•

Plant built and developed by a non-specialized

or unlicensed thermosanitary installer.

•

Failure to comply with the instructions for

Laying and Protection against external corrosion

referred to in point 11.4 below.

•

Lack of plant test and related documentation.

11.4. Laying and protection against external

corrosion

In order to avoid failure of the brass products, it is

advisable to isolate the fittings in an inspectable box or

in any case protect them with appropriate materials.

For their protection, anti-corrosion and waterproof

materials must be used, that inhibit corrosion from

possible chemical agents, and materials resistant to

heat and aging.

These installation instructions must be applied in

conjunction with the assembly instructions de

fined for

each individual product range and duly shown in the

Seller’s catalog.

S

A

L

E

C

O

N

D

I

T

I

O

N

S

A

N

D

W

A

R

R

A

N

T

Y